Author Topic: Casting and Sliding with braid  (Read 7312 times)

0 Members and 1 Guest are viewing this topic.

Offline aquadementia

  • Spineless
  • Member
  • *
  • Posts: 65
  • Cred: -9
  • Gender: Male
  • Location: Jeffreys Bay
Casting and Sliding with braid
« on: June 07, 2011, 08:31:22 PM »

ok rather start a new thread so that we dont hijack another into oblivion


Is it possible(safe & feasible) to cast a heavy sinker using a large multiplier loaded with braid topshot and then slide a bait down said topshot?


Something that has been discussed but tried by very few. So I thought I'd give it a go!


tackle used in the test
Shimano Trinidad DC30 
L&F Sharky Standard
100lb XX Viper braid
1.3mm windon leader
8oz sinker


The casting
The viper braid is pretty soft which is a disadvantage because it doesnt lift up by itself when it comes time to leave the spool on a cast, it wants to stay curled up until it gets pulled forward by the sinker. I think 30lb fireline(about 50lbs linear breaking strength) or even better fireline tracer braid which is the only braid I know of that has been optimized for casting with a multiplier, may be better options. I am going to put 65lb JBLO back onto the DC now that tarpon season is over.


Its a lot easier to get an overwind with the soft braid, but the overwinds I got didnt cut deep. Pulled out easily. I only got an overwind once I really started pushing it otherwise the casts were uneventful.


Good distance, a good 100m without much effort and a thickish leader. I had to set the digital control pretty high when using the braid, but I was still getting a decent distance, similar to what I was getting with 0.55 seagrand. With that high setting I didnt put my hand near the spool for fear of losing a thumb


verdict - well, with a DC you can get away with using soft braid, but I reckon 30lb fireline would work well... You could use the 50lb but then you would lose the distance advantage due to the thickness.





Sliding
wow! feels weird! you're only able to wiggle your tip about 6 inches from no tension to tight. It goes down not too fast so you have to shake a bit longer. My slide did get all the way down because I got epically stuck once I wanted to pull out and was pulling like a madman to get unstuck, so obviously my hooks and fouled on the rocks... eventually the 80lb dacron broke where it went single between the leader and the loop. At least I know my windons work! Thats another reason for using braid under 50lb I think, easier to break off, rather use a bimini than a stitch to weaken it a bit...




verdict - it works, just slide a bit longer. pop your sinker if you're not sure if its all the way down. Reckon its much easier to get the bait down with a non-hmg cos its wigglier. Make sure your sinker sits VAS,  a long boom is the answer.


Why use braid?
In my opinion you wont get burnt off on braid as you would on nylon.
Its thinner so with a reel that can handle it (DC, talented caster) you should get much better distance.
Its super direct so those headshakes and wing flaps will make fighting that nunu all the more adrenalin pumping!


Those are my findings, hopefully me sharing this will encourage you to try it for yourself :)


I slid the smallest shad i could find (+-40cm) but no takers

Offline Hooch

  • Banned
  • *
  • Posts: 330
  • Cred: 33
  • Gender: Male
  • Fear no Fish
  • Location: Pretoria
Re: Casting and Sliding with braid
« Reply #1 on: June 07, 2011, 09:08:42 PM »
Aqua,

So you say we should all slide with braid? Because its stronger?


Offline aquadementia

  • Spineless
  • Member
  • *
  • Posts: 65
  • Cred: -9
  • Gender: Male
  • Location: Jeffreys Bay
Re: Casting and Sliding with braid
« Reply #2 on: June 07, 2011, 11:06:20 PM »
not necessarily... It was mainly to test a theory... I will let you know once I've caught something substantial on it how it went, if my arms are still attached to my body

Offline CASTSA

  • Wesley Peens
  • Senior Member
  • **
  • Posts: 374
  • Cred: 35
  • Gender: Male
  • IT"S ALL ABOUT THE FISHING LIFE!!
  • Location: KZN - South Africa
Re: Casting and Sliding with braid
« Reply #3 on: June 08, 2011, 06:49:18 AM »
Bud, just be very careful, if you do get an over wind and it loops over and catches you finger while casting a 9oz sinker you will chop it off, and if it does cut it off you will get a serious cut.
 
Im not sure how hard you throw but even with nylon I have had some very deep cuts.............
 
If you are having issues with burn-off with sliding and using Mono then you need to look at whats causing that problem. Best why to access, take note out of ten slides, count how many times you get burnt off, if you find it is more than once or twice you need to reaccess your technique.
 
Many factors can influence,
- Length of trace
- Dynamic of bait
- Quality of slide
- Sliding off the beach or rocks
- Quality/Diameter of Mono
- Sea conditions
 
Burn off should not be an issue, only if the sea is up and its washing etc then its possible.
If I get burnt off once in 50 slides I get worried.
 
Tight lines........

Offline Kumz

  • Retired
  • *
  • Posts: 0
  • Cred: 0
  • Gender: Male
Re: Casting and Sliding with braid
« Reply #4 on: June 08, 2011, 07:28:34 AM »
Casting Baits out on Braid only No probs ... been doing that for a few years now ...
 
 
Sliding ... Eeeiiissshhh no ... I have know guys that have tried it with little success ..& one guy kept getting cut off on his mainline(braid) ..this was said to be due to the slides running on braid & slides had tiny knicks in them etc ...
It became rather expensive ....
 
My 2cs ..
 
 

Offline REEFMAN

  • Ultimate Champ
  • ****
  • Posts: 9768
  • Cred: 769
  • Gender: Male
  • Location: Jozi
Re: Casting and Sliding with braid
« Reply #5 on: June 08, 2011, 07:46:15 AM »
Nice post Chris... food for thought... +cred

I know Hooked tried sliding with braid a few years ago and was quite emphatic in saying that it doesn't work very well.
Why do you say that you won't have as many burn-offs with braid as with nylon? The way I see it (theoretically), braid has worse abrasion resistance than nylon and so will be worse than nylon??

Offline WalkersKiller

  • Fish The Sea | Fish The Fly | Gareth Roocroft
  • Ultimate Champ
  • ****
  • Posts: 7417
  • Cred: 366
  • Gender: Male
  • Conservation First!
  • Location: Edenvale, Gauteng
Re: Casting and Sliding with braid
« Reply #6 on: June 08, 2011, 08:47:25 AM »
Great post Chris +cred, some interesting points there!

Offline aquadementia

  • Spineless
  • Member
  • *
  • Posts: 65
  • Cred: -9
  • Gender: Male
  • Location: Jeffreys Bay
Re: Casting and Sliding with braid
« Reply #7 on: June 08, 2011, 09:46:31 AM »
the 100lb xx braid I'm using is about 0.50 or maybe 0.52 and its just got so much more 'substance' to it than the equivalent thickness mono. I dont think it will be affected by heat and if it does get a nick in it wont 'run' like it can with mono.


Well anyway thats my theory, will see how it pans out in the real world :dunno:



burn off's aint an issue for me at all, last time was about a year and a half ago (excluding rat greys and hammers taking baits on the way down) 

 

SimplePortal 2.3.7 © 2008-2026, SimplePortal