Author Topic: Jigging/ drop shoting & toothy critters move in  (Read 5222 times)

0 Members and 1 Guest are viewing this topic.

Offline Prego

  • Ultimate Champ
  • ****
  • Posts: 2880
  • Cred: 167
  • Gender: Male
  • Because I said so
  • Location: Glenvista, Johannesburg
Jigging/ drop shoting & toothy critters move in
« on: August 02, 2011, 11:55:18 AM »
How would one rig up a jig, spoon or drop shot jig head with wire to prevent being bitten off?

 :tkx:

Offline nico

  • The original man (*)(*)
  • Member
  • *
  • Posts: 773
  • Cred: 47
  • Gender: Male
  • Click above for cred!
  • Location: Gibraltar
Re: Jigging/ drop shoting & toothy critters move in
« Reply #1 on: August 02, 2011, 02:13:16 PM »
How would one rig up a jig, spoon or drop shot jig head with wire to prevent being bitten off?

 :tkx:

I've though about this one a bit, and tried a few things. In the end, best action for me was to haywire twist onto the jighead, 5cm of wire and then tiny swivel.
 
That said: I'd rather not use any wire at all. Sure, you will drop some fish, but the higher strike rate would compensate for this. And as Earl Strydom said to me: if you get bitten off, you should be winding faster!  :rck"

Offline Bwana

  • Ultimate Champ
  • ****
  • Posts: 916
  • Cred: 206
  • Gender: Male
  • Deep Blue Addict
  • Location: Shelly Beach, KZN
Re: Jigging/ drop shoting & toothy critters move in
« Reply #2 on: August 02, 2011, 03:13:32 PM »
On jig I ofetn use a stainless steel multi-strand assist crimped to the solid ring, this prevents bite-offs on the assist but not above the jig on the leader. I normally prefer more hookups and risk losing one or two jigs to couta or wahoo than going for any steel above the jig onto the leader - not good for strikes.


On dropshot - very similar to what Nico said - I use 10cm of #6 wire and then albright knot to the leader. It doesn't affect the action of the dropshot too much and is good insurance if you do hook a toothy critter....


Here's a pic of the s/s assist from Williamson, except I carry the heatshrink over the eye of the assist hook to keep it stiff. Also, don't rig your assist hook the way their pic shows, rather have your assist onto a solid ring or grommet and then run your jig off a split-ring that way your hook is directly connected to the leader and if another fish grabs the jig while you are fighting a fish the split ring will pull open and you are still connected to the assist and just lose the jig....


« Last Edit: August 02, 2011, 03:16:59 PM by Bwana »

Offline Prego

  • Ultimate Champ
  • ****
  • Posts: 2880
  • Cred: 167
  • Gender: Male
  • Because I said so
  • Location: Glenvista, Johannesburg
Re: Jigging/ drop shoting & toothy critters move in
« Reply #3 on: August 02, 2011, 03:53:50 PM »
Thanks Bwana + cred

Just one thing, for the jig head are you tying the steel onto the leader without a swivel??  :cnfzd
« Last Edit: August 02, 2011, 03:54:14 PM by Prego »

Offline Bwana

  • Ultimate Champ
  • ****
  • Posts: 916
  • Cred: 206
  • Gender: Male
  • Deep Blue Addict
  • Location: Shelly Beach, KZN
Re: Jigging/ drop shoting & toothy critters move in
« Reply #4 on: August 02, 2011, 04:08:35 PM »
@Prego - I know it sounds strange! You are basically making a loop end in the steel and tying the MONO around the steel wire using the ALBRIGHT KNOT:


See Reefman's post on how it works here:


http://www.ultimateangling.co.za/index.php/topic,69.msg130.html#msg130


If tied correctly, lubricated and seated properly it is very strong and is less visible than other connections  :clwn


Offline Prego

  • Ultimate Champ
  • ****
  • Posts: 2880
  • Cred: 167
  • Gender: Male
  • Because I said so
  • Location: Glenvista, Johannesburg
Re: Jigging/ drop shoting & toothy critters move in
« Reply #5 on: August 02, 2011, 04:11:19 PM »
Thanks I was busy reading it when you posted. I will give it a shot.

 :tkx: again.

Offline Capt. Hook

  • Official ball thrower for my dog
  • Ultimate Champ
  • ****
  • Posts: 3140
  • Cred: 338
  • Gender: Male
  • Location: Durbs
Re: Jigging/ drop shoting & toothy critters move in
« Reply #6 on: August 02, 2011, 07:06:27 PM »
I agree with Nico, short piece of wire max 5cm with haywire onto jig head and a small centro size 14 swivel, this works well for me and even for Tigers with out problem. Just make a decent size loop on the haywire to allow the jig head free movement.

Offline Prego

  • Ultimate Champ
  • ****
  • Posts: 2880
  • Cred: 167
  • Gender: Male
  • Because I said so
  • Location: Glenvista, Johannesburg
Re: Jigging/ drop shoting & toothy critters move in
« Reply #7 on: August 02, 2011, 11:23:36 PM »
FA I will try the method you & Nico mentioned too.

 :tkx:

Offline Capt. Hook

  • Official ball thrower for my dog
  • Ultimate Champ
  • ****
  • Posts: 3140
  • Cred: 338
  • Gender: Male
  • Location: Durbs
Re: Jigging/ drop shoting & toothy critters move in
« Reply #8 on: August 02, 2011, 11:33:27 PM »
FA I will try the method you & Nico mentioned too.

 :tkx:
I like to use a split ring so it is easy to change from jig heads to spoons to lures etc.

 

SimplePortal 2.3.7 © 2008-2026, SimplePortal