Author Topic: FG Knot  (Read 28130 times)

0 Members and 2 Guests are viewing this topic.

Offline Trevour

  • Senior Member
  • **
  • Posts: 97
  • Cred: 3
  • Gender: Male
  • Location: Gauteng
Re: FG Knot
« Reply #20 on: January 19, 2015, 08:48:47 PM »
Hi guys,

I see some do and some don't recommend the knot for casting. Are there any extra pointers as far as the guides and rod setup that may assist with a braid to mono leader. For instance, will the knot pass through low riders etc. And do smaller diameter reels that release line in smaller loops help?

And can anyone shead light on why braid to mono gives so many problems, we cast biminis, catpaws and fig 8's with mono to mono, but even tiny knots cause problems with braid.


Offline SAfish

  • Angler of the Month - April 2015
  • Ultimate Champ
  • ****
  • Posts: 4238
  • Cred: 137
  • Gender: Male
  • Location: Knysna, South Africa
Re: FG Knot
« Reply #21 on: January 19, 2015, 09:33:37 PM »
Trevour, it is simple, don't let the knots pass through your guides. I had no problems since I stopped using long leaders, I now only have a short leader and check my braid for wear often. Get a good casting braid, it is worth the bucks.

Offline Johane

  • Member
  • *
  • Posts: 8
  • Cred: 0
  • Gender: Male
  • Location: Cannon Rocks,Eastern Cape
Re: FG Knot
« Reply #22 on: January 20, 2015, 06:48:21 PM »
Here is another version which works quite well https://www.youtube.com/watch?v=52uWL43hUbw

Offline krissi

  • Ultimate member
  • ***
  • Posts: 789
  • Cred: 137
  • Gender: Female
  • Location: Underberg, KZN
Re: FG Knot
« Reply #23 on: January 20, 2015, 07:10:29 PM »
That looks very do-able.  Thanks Johane  :bow:

Offline Alf03

  • Member
  • *
  • Posts: 50
  • Cred: 2
  • Gender: Male
  • Location: Grahamstown eastern cape
Re: FG Knot
« Reply #24 on: March 20, 2016, 10:35:07 AM »
I have been practicing this knot and I am going to try it on GTs in kosi. Anyone had any bad experiences with knot strength using it?

Offline FishStyx

  • Ultimate Champ
  • ****
  • Posts: 3007
  • Cred: 51
  • Gender: Male
  • I fish, therefore I am.
  • Location: Louist Trichardt, Limpopo
Re: FG Knot
« Reply #25 on: March 21, 2016, 07:37:28 AM »
Personally never had one fail on me. Trick is to keep the braid turns tight and bunched together, and to put the knot under a lot of strain before clipping the tag on the leader.
Forgive me Father for I have spinned... It's been three weeks since my last cob session.

Offline Alf03

  • Member
  • *
  • Posts: 50
  • Cred: 2
  • Gender: Male
  • Location: Grahamstown eastern cape
Re: FG Knot
« Reply #26 on: March 21, 2016, 08:02:43 AM »
Think I have got it right. Tested the last knot I made couldn't break it. Tied my line around a concrete and steel pole and pulled as hard as I could!

Offline Vandit

  • Senior Member
  • **
  • Posts: 85
  • Cred: 1
  • Gender: Male
  • Location: Pretoria
Re: FG Knot
« Reply #27 on: March 21, 2016, 09:28:05 AM »

And can anyone shead light on why braid to mono gives so many problems, we cast biminis, catpaws and fig 8's with mono to mono, but even tiny knots cause problems with braid.

I reckon there is culmination of two reasons for this on fixed spool reels:

1.) Large differences in elasticity (stretch): When casting off of braid with a leader that is not completely out the guides, i.e. with a knot in the guide train, the leader absorbs the majority of the elastic energy before release.  This is because it has a much lower modulus of elasticity and thus stretches considerably more for a given diameter.  As you release during the cast all this energy has to go somewhere - it goes into pulling extra line off the spool, much faster than the speed at which the casted projectile flies, resulting with excess line in the guide train.  With a long mono leader this also happens but mono is much stiffer and heavier (it doesn't bunch up and flap around) so it contracts like a coil spring. Braid on the other hand doesn't have as much "memory" and is much lighter causing it to bunch up in an erratic fashion causing guide wraps, wind knots and the like. This effect is only momentary, as soon as the casted projectile reaches the length of extra line pulled off during the strain energy release, it continues to peel line off at it's speed.   This is easily solved in two ways - casting off a long leader with wraps on the spool or a short leader out the guides.


2.) Large differences in mass or rather an abrupt transition in mass:  The intuitive understanding of line coming of a fixed spool reel is essentially a coil of rope pulled into a straight line. This is somewhat true for the first layer on the spool, when the diameter is the same as the spool lip.  But as the the spool starts emptying, the line has to be pulled around the spool lip.  For low line speeds, this makes near as no difference.  But when the line speeds are high enough for momentum effects to become apparent, things become interesting. The direction of line momentum has to change from initially pointing towards the spool lip to finally pointing to the centre of the first guide.  Consider this analogy:

https://www.youtube.com/watch?v=DDSRsMGbNV8

Here the momentum change is from initially pointing upward to finally pointing downwards.  For low speeds the momentum can be changed quickly (seemingly on the lip of the jar), for high line speeds this happens over a greater distance.

Now this is not exactly the same as what happens on a fixed spool reel but the fundamentals remain the same.

The problem comes in when the join of nylon and braid has to pass through this.  Imagine having a skip rope with one half length chain and the other half string.  Imagine how that would look when spinning around.........  The mass transition of the nylon to braid is exactly this - the braid doesn't have enough mass to keep that smooth change in momentum (stabilise the nylon).  The nylon end thus flails about uncontrolled in a larger arc causing rod slap etc.  This all results with a higher propensity for guide wraps.  This doesn't necessarily mean that only the first guide is at risk, this disturbance is passed along the entire rod - but the probability does decrease towards the tip.

Theoretically there are few remedies for this:
- A properly set out guide train to manage exactly this (Avoiding massively inappropriate spacing between guides or the spool for instance... Unlike the.. Assassin Horizon... cough cough)
- Casting off a properly filled spool
- Tapered leaders - the mass transition is not as abrupt but I doubt many would follow suite due to price


There may also be other phenomena that cause issues, this is just given to show that there is much more at work than just knot size.
« Last Edit: March 21, 2016, 11:31:02 AM by Vandit »

Offline REEFMAN

  • Ultimate Champ
  • ****
  • Posts: 9768
  • Cred: 769
  • Gender: Male
  • Location: Jozi
Re: FG Knot
« Reply #28 on: March 21, 2016, 10:56:34 AM »
Excellent post Vandit!  :+ cred:

Offline Trevour

  • Senior Member
  • **
  • Posts: 97
  • Cred: 3
  • Gender: Male
  • Location: Gauteng
Re: FG Knot
« Reply #29 on: March 21, 2016, 11:28:19 AM »
Nice post Vandit. With regards to the video, I would suspect those beads are performing much like mono would, whereas braid would go straight over the rim with little or no 'loop' above it. I've always suspected the difference in suppleness between the line types being the main problem, which is why even an fg is not foolproof. Does anyone using braid as mainline on a multiplier with a fluoro/mono leader have any feedback. Can bigger knots be used? This should give us an indication as to what extent the coils on a grinder are responsible for the problems.

Offline Vandit

  • Senior Member
  • **
  • Posts: 85
  • Cred: 1
  • Gender: Male
  • Location: Pretoria
Re: FG Knot
« Reply #30 on: March 21, 2016, 11:52:32 AM »
The momentum direction changes on a spinning reel will be vastly more complicated than this.  The take home message really is that an abrupt change in mass will change how momentum is conserved.  To visualise this consider how the chain almost makes a standing wave or 'loop' under steady state, now consider how this loop swings when the end of the chain is reached (no more mass behind to stabilise it).  This is perfectly analogous to a braid mono connection.  It is this swinging end that creates wraps and the associated havoc.
« Last Edit: March 21, 2016, 12:10:33 PM by Vandit »

Offline Alf03

  • Member
  • *
  • Posts: 50
  • Cred: 2
  • Gender: Male
  • Location: Grahamstown eastern cape
Re: FG Knot
« Reply #31 on: March 21, 2016, 12:06:16 PM »
Nice post Vandit. With regards to the video, I would suspect those beads are performing much like mono would, whereas braid would go straight over the rim with little or no 'loop' above it. I've always suspected the difference in suppleness between the line types being the main problem, which is why even an fg is not foolproof. Does anyone using braid as mainline on a multiplier with a fluoro/mono leader have any feedback. Can bigger knots be used? This should give us an indication as to what extent the coils on a grinder are responsible for the problems.

I do not recommend using braid as a main line on a multiplier. Especially if you enjoy having a thumb!  I am not aware of anyone fishing with a braid mainline on a multiplier due to this. You can just imagine getting a finger in a birds nest while casting. The cuts are bad enough with nylon!

Offline Trevour

  • Senior Member
  • **
  • Posts: 97
  • Cred: 3
  • Gender: Male
  • Location: Gauteng
Re: FG Knot
« Reply #32 on: March 21, 2016, 01:04:39 PM »
Hi again Vandit, I found this video https://youtu.be/YZ1-4DVLSZ0, as an explanation for the wave effect with the beads. It suggests that a change in flexibility rather than mass is the reason for the problem, in other words the properties of the material rather than its mass is the problem. To visualize - if you double braid and lay the two lines next to each other and leave them alone, they will remain next to each other, and the loop formed will be small, where with mono the two lines would separate leaving a larger loop. This being a result of the lines ability or lack thereof to change direction. In other words a chain followed by piano wire may maintain the wave, even though the wire has less mass than a rope.

Offline Vandit

  • Senior Member
  • **
  • Posts: 85
  • Cred: 1
  • Gender: Male
  • Location: Pretoria
Re: FG Knot
« Reply #33 on: March 21, 2016, 03:24:34 PM »

Hi again Vandit, I found this video https://youtu.be/YZ1-4DVLSZ0, as an explanation for the wave effect with the beads. It suggests that a change in flexibility rather than mass is the reason for the problem, in other words the properties of the material rather than its mass is the problem. To visualize - if you double braid and lay the two lines next to each other and leave them alone, they will remain next to each other, and the loop formed will be small, where with mono the two lines would separate leaving a larger loop. This being a result of the lines ability or lack thereof to change direction. In other words a chain followed by piano wire may maintain the wave, even though the wire has less mass than a rope.

Hi Trevour,
Agreed, dynamics is a two sided coin in that mass as well as stiffness will govern the mode shapes (the shape of the "standing waves").  That is, the piano wire argument would be a meritorious solution.  My argument lies in the fact the mode shapes exist due to acceleration which can only act on mass, or rather inertial forces.
« Last Edit: March 21, 2016, 08:03:05 PM by Vandit »

Offline Zak-e-Boy

  • Ultimate member
  • ***
  • Posts: 186
  • Cred: 13
  • Gender: Male
  • Everyday's a Holiday - Umhlanga
  • Location: Umhlanga
Re: FG Knot
« Reply #34 on: March 22, 2016, 03:47:34 PM »
Eish, men..interesting subject.  No offence, but I think some of you guys need to get down to a lower altitude where the salt water is. It appears that the high altitude, fresh water and the lack of fishing is doing something strange to you guys up there ?  w;k   

Offline Trevour

  • Senior Member
  • **
  • Posts: 97
  • Cred: 3
  • Gender: Male
  • Location: Gauteng
Re: FG Knot
« Reply #35 on: March 22, 2016, 05:07:02 PM »
Eish, men..interesting subject.  No offence, but I think some of you guys need to get down to a lower altitude where the salt water is. It appears that  :sailf:the high altitude, fresh water and the lack of fishing is doing something strange to you guys up there ?  w;k

This is how gauteng does saltwater fishing in the off season! On the bright side Ill get my fix starting tomorrow with a ten day trip to Mpame Transkei.

Vandit! Once solution 1 and 2 are in place, solution 3 is an issue. The  expense (not such a big problem), but for eg with 30 lbs line, the leader would be at least .50 after the taper to ensure it breaks beyond 30lbs with some change, I think our mass and stiffness priblem will still exist. I was thinking taking care of the problem on the braid side of the join, by inserting a length of mono. It would need to be at least the length as the distance from first guide to the reel, and would need to twist (fairly big twists) around the braid. It would also if possible not take pressure when pulling hard (ie not act a a double line as in biminis etc, but merely take care of the huge and sudden loss of mass and stiffness.

Offline Zak-e-Boy

  • Ultimate member
  • ***
  • Posts: 186
  • Cred: 13
  • Gender: Male
  • Everyday's a Holiday - Umhlanga
  • Location: Umhlanga
Re: FG Knot
« Reply #36 on: March 22, 2016, 05:32:49 PM »
Trevour, enjoy your trip and tight lines !!

Offline colin

  • Ultimate Champ
  • ****
  • Posts: 752
  • Cred: 13
  • Gender: Male
  • Location: Kelland , Randburg
Re: FG Knot
« Reply #37 on: March 22, 2016, 05:33:08 PM »
[quote author=Zak-e-Boy
Eish, men..interesting subject.  No offence, but I think some of you guys need to get down to a lower altitude where the salt water is. It appears that the high altitude, fresh water and the lack of fishing is doing something strange to you guys up there ?  w;k
 :corrct: :corrct:

 :lolo:  :dunno: :dunno: :dunno: lotsa big words for a old timer smous. :hehe: :toppie:
My wife allows me to keep all the fishing tackle I can hide.

Offline REEFMAN

  • Ultimate Champ
  • ****
  • Posts: 9768
  • Cred: 769
  • Gender: Male
  • Location: Jozi
Re: FG Knot
« Reply #38 on: March 22, 2016, 05:39:18 PM »
On the bright side Ill get my fix starting tomorrow with a ten day trip to Mpame Transkei.


Bastid...! Your punishment for tormenting us is a full report please!!
Awesome place.
 :tite

Offline Vandit

  • Senior Member
  • **
  • Posts: 85
  • Cred: 1
  • Gender: Male
  • Location: Pretoria
Re: FG Knot
« Reply #39 on: March 22, 2016, 11:01:09 PM »
Vandit! Once solution 1 and 2 are in place, solution 3 is an issue. The  expense (not such a big problem), but for eg with 30 lbs line, the leader would be at least .50 after the taper to ensure it breaks beyond 30lbs with some change, I think our mass and stiffness priblem will still exist. I was thinking taking care of the problem on the braid side of the join, by inserting a length of mono. It would need to be at least the length as the distance from first guide to the reel, and would need to twist (fairly big twists) around the braid. It would also if possible not take pressure when pulling hard (ie not act a a double line as in biminis etc, but merely take care of the huge and sudden loss of mass and stiffness.


Imagine being on the beach and having to explain to other fishos what the hell you are doing tying that... And then trying to to explain the mass - stiffness dilemma... I would love to see that sight with a beer in hand.


I reckon the ultimate implementation would be using hollow braid.  FG to leader and splice a few inches behind the knot into the braid. Get a 9ft tapered fly fishing leader (appropriately sized) and splice it into the braid behind this.  This would ensure a gradual transition of both mass and stiffness with such a long taper to such a thin end.  And the splicing shouldn't interfere with the line strength.


Would I go this far though?  To test the hypothesis perhaps once at a damn somewhere (social maybe).  I doubt I'd rock up somewhere to actually fish with it though.

 

SimplePortal 2.3.7 © 2008-2026, SimplePortal