Author Topic: John F's DIY: Small Tips & Tricks  (Read 118499 times)

0 Members and 1 Guest are viewing this topic.

Offline fish4fun

  • Member
  • *
  • Posts: 25
  • Cred: 14
  • Location: Duban
Bait preparation - cleaning
« Reply #80 on: May 17, 2017, 08:21:17 PM »
Not sure if this has been mentioned before on this topic, but rock and surf fishing involves preparing bait. preparing bait leaves slimy, slippery , bloody residue on your hands which dirties your tackle and interferes with your casting. Using a car chamois, obtainable at a low cost, place it in your water bucket. When wet, it strips bait residue and mess off your hands like nothing else, much better than a towel, T shirt or - shudder - your shirt and shorts. Before casting, wring out the chamois and, once dry, use it to dry your hands ...for some reason it really dries out your hands and allows you to grip your rod and control your reel very well and eliminates slippage and mess. Once at home, it does get a little funky if not cleaned- just leave it in a bucket with water and diluted bleach overnight - good as new!  :brnz:

Offline John F

  • Moderator
  • *****
  • Posts: 6563
  • Cred: 522
  • Gender: Male
  • Virtus et Honos
  • Location: Maputo - Mozambique
Re: John F's DIY: Small Tips & Tricks
« Reply #81 on: May 17, 2017, 09:39:48 PM »
It certainly wasn't mentioned before... thanks! Your tip doesn't sound very practical for offshore use, however I'm sure the R&S gang will make good use of it.
Acecraft 660 DV
Yeld cat 19 (Sold)
Gemini 520 Crusader (Sold)

Offline John F

  • Moderator
  • *****
  • Posts: 6563
  • Cred: 522
  • Gender: Male
  • Virtus et Honos
  • Location: Maputo - Mozambique
Re: John F's DIY: Small Tips & Tricks
« Reply #82 on: October 12, 2017, 12:28:07 PM »
Bringing back the shine on rusted S/S tools

Every saltwater angler worth its salt, knows that all s/s tools (be it knifes, pliers, etc.) will rust... it actually starts were it reads "Stainless" :hehe:

The rust spots accumulate and suddenly the tool looks terrible and ends up in the dust bin. My diving knives were almost going in that direction. Luckly, I don't have a diving shop nearby. So I made a plan. Used vinegar (synthetic, the cheapest I could find). Submersed my knives in a bottle of water for 24 h. Used steel wool to scratch the rust away. Some stubborn stains required extra time in the vinegar.

Job's done and tools are ready to work for a few more years. And I saved some cash for fuel or extra tackle :hyst:
Acecraft 660 DV
Yeld cat 19 (Sold)
Gemini 520 Crusader (Sold)

Offline Serra Moz

  • Ultimate member
  • ***
  • Posts: 477
  • Cred: 12
  • Gender: Male
  • Location: Marracuene - Mozambique
Re: John F's DIY: Small Tips & Tricks
« Reply #83 on: October 13, 2017, 01:39:38 AM »
Thanks for sharing
Happy days!

Offline Sherwyn King

  • Member
  • *
  • Posts: 1
  • Cred: 0
  • Gender: Male
  • Location: Durban
Re: John F'S DIY: Small Tips & Tricks
« Reply #84 on: March 06, 2019, 02:53:00 PM »
"Humidity is a killer for tackle (both reels, terminal tackle and tools) and once the basic washing is done (and the tackle looks dry) I bet everybody just packs their tackle and stores it away. The reels will still be damp inside for a week or so and there will always be a bit of humidity in your tackle box. Here's a trick to help keep things a bit dryer - Silica bags. Every electrical/electronic appliance (and even shoes!) come with silica bags these days. When packing your reels with the neoprene covers, keep at least one or two inside the reel covers. Put a lot more in your tackle box. Every now and then take the bags out and put then in the oven for about 30 minutes at 60o to extract the humidity. This will surely help maintain your tackle."

Two cents worth .Kitty litter is pure silica and is available quiet cheap from your pet stores or Builders.Add a hand full to a old sock and place in tackle bag.
Thanks again John :happ:   :+ cred:

 

SimplePortal 2.3.7 © 2008-2026, SimplePortal