ULTIMATE ANGLING - the Ultimate SA Fishing website

General Angling Topics => Shore Angling => Topic started by: Habib on August 17, 2011, 10:10:47 PM

Title: how to make your slide sinker hold vas
Post by: Habib on August 17, 2011, 10:10:47 PM
hi.....
 
in the spirit of sharing
 
biggest most annoying factor of sliding is having your sinker come loose on a big bait while sliding.
 
now not everyone can cast out a 10 ounce sinker which is usualy required when slding a big bait. also a smaller sinker like an 7 or 8 ounce is more comfortable to cast and usually allows you to swing harder thus giving you a better and further cast.
 
i dont like to use cable ties etc on sinkers to hold the wire in place.
 
following my story is a series of pics on how to adapt your sinker for a better holding/grip so you can shake like a vitto after he chowed a durban extra hot bunny and still have your sinker hold.
 
bigger bait...bigger fish. so now you can slide a whole bonnie on a 7 ounce
 
tight lines all.......
Title: Re: how to make your slide sinker hold vas
Post by: Habib on August 17, 2011, 10:13:16 PM
take your slide sinker...i prefer using the long boom. all you need is a hammer or plier and a screwdriver/nail . the screwdriver/nail shaft diameter needs to be wider than the grooves in the sinker that the wire sits in.
 
 
Title: Re: how to make your slide sinker hold vas
Post by: Habib on August 17, 2011, 10:15:34 PM
as in the pic...place the screwdriver on the groove and hammer it until the groove gets deeper. lead is pretty soft so just a few taps will do. tap it until the screwdriver level is with the sinker....or however deep u wana tap it
Title: Re: how to make your slide sinker hold vas
Post by: Habib on August 17, 2011, 10:17:48 PM
this is what it should look like. a nice deep groove. i decreased the brightness of the pic so you can see the groove, apologies, im not the best photographer in the world.
Title: Re: how to make your slide sinker hold vas
Post by: Habib on August 17, 2011, 10:20:11 PM
i always rebend the wires to a shrper, straighter bend. they never seem to come properly bent from the shops. bending it like so will make it sit better in the grooves and makes it very difficult to slip out
Title: Re: how to make your slide sinker hold vas
Post by: Habib on August 17, 2011, 10:21:54 PM
clip in place and u now have a PROPPER sinker that will sit like sheet.
Title: Re: how to make your slide sinker hold vas
Post by: Homie on August 17, 2011, 10:24:27 PM
 :udman:

Thats a  :win:
Title: Re: how to make your slide sinker hold vas
Post by: John F on August 17, 2011, 10:27:15 PM
 :shre: :win: +cred!
Title: Re: how to make your slide sinker hold vas
Post by: Habib on August 17, 2011, 10:28:57 PM
for added grip....bend the tips up a bit. helps alot in sandy areas. especially on the north coast were the sand is a bit more coarse and sinkers battle to grip.
 
after the cast, give your sinker a minute or 2 to settle and then slide. i normally put my sinker out and then go prepare the bait.
 
dont be scared that you might not release the sinker. 9 times out of 10, when you reel the sinker in, the wires were still bent in place on the sinker. just put your rod tip down and reel in. i never had a problem releasing sinkers. i use a minimum of a 0.80 sinker line.
 
go out there....cast a sinker, put a whole dead bait out.....and get torn.
 
 
ciao
Title: Re: how to make your slide sinker hold vas
Post by: Nemesis. on August 17, 2011, 10:52:05 PM
Nice one Zeyn, another way to get your sinker to sit in quicker is to hold your rod horizontally,parallel to the ground after your have casted. Then gently move the rod back and forth in that position. It helps the sinker dig in better because of the smaller angle(between your rod and sinker), then holding the rod upright and trying to lock the sinker in the sand.
Title: Re: how to make your slide sinker hold vas
Post by: Habib on August 17, 2011, 11:12:25 PM
hahahaha sorry guys
 
try it guys, really works. i was sliding whole bonnies at mtunzini on 7 ounce sinkers. it sits very well.
 
also remember the angle you bend you wires plays a huge roll. dont over bend them. 45 degrees is good enough
 
i hope the last 2 tips (modify clip and now sinker) will help all u sliders out there.
 
 :dwa:
Title: Re: how to make your slide sinker hold vas
Post by: Manuel Junior on August 17, 2011, 11:24:45 PM
 :shre: (clap)
Title: Re: how to make your slide sinker hold vas
Post by: Kumz on August 18, 2011, 07:26:04 AM
 (clap) ....  :shre: ......  :win:
Title: Re: how to make your slide sinker hold vas
Post by: m@rius on August 18, 2011, 08:14:08 AM
Awesome Habib, you've been putting up some top-class posts recently
Title: Re: how to make your slide sinker hold vas
Post by: aquadementia on August 18, 2011, 09:46:22 AM
great tip uncle  :shre:
 
+cred
Title: Re: how to make your slide sinker hold vas
Post by: Habib on August 19, 2011, 09:35:34 PM
thanks my boy
SimplePortal 2.3.7 © 2008-2026, SimplePortal