ULTIMATE ANGLING - the Ultimate SA Fishing website

General Angling Topics => Shore Angling => Topic started by: Heinz on June 22, 2021, 09:18:23 PM

Title: Shad on circle hook
Post by: Heinz on June 22, 2021, 09:18:23 PM
Believe it or not. I am struggling to catch shad. I get very frustrated when people all around are pulling them out. I am battling to hook these fish. As far as I can see I'm doing what the others are doing. I am using braid so I am not sure how hard to strike. I am wondering if using circle hooks will help. If so can anybody please advise me re the technique to use.
Thanks
Title: Re: Shad on circle hook
Post by: ianf on June 23, 2021, 08:33:31 AM
I understand your frustration. It happens to all of us at some stage. You are not alone.


What size hook are you using? I normally use a 5/0 for targeting shad, with a 0.8 hook snoot so that the shad do not bite through it. Sometimes the steel trace puts them off. Other things I have found that can make a difference: -
If the rod is not stiff enough, when you strike, the rod is still bending, and the shad is already gone, having gorged himself on your bait.
Sometimes change strategy....go from fishing a 3 way swivel (with or without a cork) to a drift bait, to a drift bait with a ball sinker.
If shad are full on the bite, try a spoon (I like the Halco twisty....have caught lots of shad on them), or even a lure (a nice purple Onde). Remember to replace the triple hook with a single (I use a 5/0 Mustad Hoodlum - nice strong hook. I VERY gently ease it open at the top with a side cutter and put it directly onto the lure. This way the hook always faces up and you are less likely to catch other lines in the water and less likely to get caught on rocks). Shad attack the rear of the fish, and getting a 3 way hook out of a shad's mouth when he has taken all 3 hooks is not fun.


Keep trying.....


Title: Re: Shad on circle hook
Post by: REEFMAN on June 23, 2021, 08:43:17 AM
Try this system, if all else fails. Only need to use the one hook though. Cast it out and retrieve it slowly on the top water.

http://www.ultimateangling.co.za/index.php?topic=5601.msg73690#msg73690
Title: Re: Shad on circle hook
Post by: PRENO on June 23, 2021, 09:54:52 AM
Good day


I had the same issue as you until I noticed the smaller fish where eating the bait out first before the shad even had a chance to.
I buy the standard ready made two hook trace from the tackle shops, its around R 15 to R 20, depending where you purchase them.
Depending on the sea conditions, I use a 1oz to a 3oz sinker on a three way swivel.
Make sure the bait is not too frozen where you will have a hard time when threading the hook. also too soft bait will become messy around the belly area and the smaller fish will peck at it.
The positioning of the hooks is of importance, longer snoot length hook, place it round 1 or 2 cm away from the tail, second hook, just above the belly, try not to hook the belly area as this makes it easier for smaller fish, also check there is no kink on the steel wire as Shad tend to bend the wire when thrashing about  and that the hooks are protruding from the sardine.
When you wrap with cotton (I normally use the Latex cotton pro thin which is ideal) make sure it is well wrapped and cut the tail fins and throw.
If the Shad is there, you will definitely hook into them, if the Shad is on a slow bite, your bait might be pecked at by smaller fish and you can try a toby spoon until the bites pick up.







Title: Re: Shad on circle hook
Post by: Davo on June 23, 2021, 10:12:29 AM
Hi


When I fish for shad i dont strike, I prefer to reel down hard and once my rod tip is pointing down a bit ill give a small jerk just to make sure that the hook has set. Any bit of slack and the shad is off so keeping constant tension on the line will get you your shad. :shd: :shd: :shd:
Title: Re: Shad on circle hook
Post by: Heinz on June 23, 2021, 07:22:33 PM
First of all.Thank you for taking the trouble to answer my post. It is most appreciated. Reading your posts I seem to have the right bait setup. I have occasions when the shad has just grabbed the bait. No problems there. It is when they are skelm that I battle. When they rattle the bait I either strike too soon or miss them completely. I thought of cutting off the head and putting the hook in the bloody end. Any thoughts about that?
Secondly. My son in law and grandson have come in from out of the country and we are going to be down at Leasure Bay for 10 days and I want them to experience the thrill of catching shad, especially my 12 year old grandson. Any tips about fishing at Leasure Bay?
Once again thanks a stack
Title: Re: Shad on circle hook
Post by: keane on June 24, 2021, 07:58:41 AM
Shad should be plentiful at Leisure Bay, can I suggest that you try making your traces using 3'0 or even 4'0 VMC needle point hooks, if you can get them. For some reason these hooks are very scarce these days, alternately use the Mustad needle point hooks in the same size. Use either a drift bait trace with a small barrel sinker or a normal shad trace with no more than a 2 ounce sinker, 3 ounce max.   
Title: Re: Shad on circle hook
Post by: PRENO on June 24, 2021, 09:26:49 AM
I thought of cutting off the head and putting the hook in the bloody end. Any thoughts about that?




My dad uses this method and works well.
SimplePortal 2.3.7 © 2008-2026, SimplePortal