« previous next »
Pages: [1] 2   Go Down

Author Topic: D.I.Y Non Return Slides  (Read 47828 times)

0 Members and 1 Guest are viewing this topic.

Offline Nemesis.

  • The Karou Charou
  • Senior Member
  • **
  • Posts: 182
  • Cred: 66
  • Gender: Male
  • Location: Mandeni _ KZN Northcoast
D.I.Y Non Return Slides
« on: December 29, 2011, 08:44:08 PM »
I used to buy Non Return Clips from off the shelf at a local tackle shop, but I found that they are always fitted with those crappy swivels, that tend to stretch and break when on to a good fish, and besides that, they have become quite expensive as off late. So I decided to fiddle around and make my own slides.This is a regular slide for live baits, for frozen/whole baits, I add a 1/4 Oz  to   1/2 Oz weight to the arm above the swivel.Thought I'd share how i make my slides, enjoy w;k


1.First step was sourcing the material, i managed to get hold of 2.0mm stainless steel rods from a friend, there after i purchased some 160lb power swivels and beads.The tools i needed were a side cutter, long nose pliers, flat head screw driver and a 8mm bolt.

2.Step two, measure a tag end of about 20cm on the wire rod, turn the tag end 5 and a half times around the bolt to create the loops of the non return slide



3.Step three, make sure the two ends of the wire rod face in opposite directions

4.Step four   , now take your flat head screw driver   and evenly space the loops. Leave enough space for thick leaders to fit in between the loops.


5.Step five, now bend the locking loop in the tag end with a long nose pliers, this will be the loop that prevents your slide from opening up whilst shaking it down to the stopper.Make sure to sand   any sharp ends that may cut you off if the clip gets tangled.


6.Step six, now you need to bend two 90 degree bends, first one will be to the height of the locking clip or slightly longer, the second bend will make up the "arms" of the clip.


7.Step seven, insert your bead.The bead prevents the coil/loop section from collapsing whilst fighting a big fish.There after bend the   clips arm to your desired angled and length.


8.Step eight,Bend a loop in the arm to which your swivel will be attached


9.Step nine, the final step. Twist 2 or 3 loops of the tag end around the clips arm.I opted to bend loops around the arm, rather then to braze the swivel loop closed, as i just don't trust that tiny bit of brazing to hold up against a big fish that might rap the trace around itself.
« Last Edit: December 29, 2011, 10:04:12 PM by Nemesis. »
Logged
There's a fine line between fishing and just standing on the shore like an idiot.

Offline Searaider

  • Ultimate member
  • ***
  • Posts: 290
  • Cred: 37
  • Gender: Male
  • Location: Randburg Gauteng
Re: D.I.Y Non Return Slides
« Reply #1 on: December 29, 2011, 09:20:04 PM »
 :shre: :+ cred:
Logged

Offline MIKE PIKE

  • Ultimate Hero
  • *****
  • Posts: 3886
  • Cred: 196
  • Gender: Male
Re: D.I.Y Non Return Slides
« Reply #2 on: December 29, 2011, 09:22:32 PM »
 (clap) ..... excellent post and tutorial Nemesis.. :appr: ... :+ cred: .
Logged

Offline Nemesis.

  • The Karou Charou
  • Senior Member
  • **
  • Posts: 182
  • Cred: 66
  • Gender: Male
  • Location: Mandeni _ KZN Northcoast
Re: D.I.Y Non Return Slides
« Reply #3 on: December 29, 2011, 09:40:40 PM »
Thanks guys :yipee:
Logged
There's a fine line between fishing and just standing on the shore like an idiot.

Offline SAfish

  • Angler of the Month - April 2015
  • Ultimate Champ
  • ****
  • Posts: 4238
  • Cred: 137
  • Gender: Male
  • Location: Knysna, South Africa
Re: D.I.Y Non Return Slides
« Reply #4 on: December 29, 2011, 09:52:44 PM »
Great tutorial.  (clap) Nominated for post of the month. http://www.ultimateangling.co.za/index.php/topic,7789.new.html#lastPost
Logged

Offline Nemesis.

  • The Karou Charou
  • Senior Member
  • **
  • Posts: 182
  • Cred: 66
  • Gender: Male
  • Location: Mandeni _ KZN Northcoast
Re: D.I.Y Non Return Slides
« Reply #5 on: December 29, 2011, 10:06:15 PM »
Quote from: SAfish on December 29, 2011, 09:52:44 PM
Great tutorial.  (clap) Nominated for post of the month. http://www.ultimateangling.co.za/index.php/topic,7789.new.html#lastPost
Thanks for the nomination buddy.Much appreciated :tkx:
Logged
There's a fine line between fishing and just standing on the shore like an idiot.

Offline Habib

  • Senior Member
  • **
  • Posts: 243
  • Cred: 56
  • Gender: Male
  • Location: pmb
Re: D.I.Y Non Return Slides
« Reply #6 on: December 29, 2011, 10:14:52 PM »
excellent excellent. gonna save us alota money bhorsri boy. have some credik
Logged

Offline Manuel Junior

  • Ultimate member
  • ***
  • Posts: 579
  • Cred: 35
  • Gender: Male
  • Location: Maputo,Mozambique
Re: D.I.Y Non Return Slides
« Reply #7 on: December 30, 2011, 07:59:16 AM »
 :shre:  Nice post  Nemesis. :+ cred:
Logged

Offline super_daav

  • Ultimate member
  • ***
  • Posts: 855
  • Cred: 74
  • Gender: Male
  • Lower Zambezi 2009
  • Location: Durban, KZN
Re: D.I.Y Non Return Slides
« Reply #8 on: December 30, 2011, 08:14:38 AM »
Excellent post!  :+ cred:
Logged
Kingfisher.co.za
Official Daiwa agent

Offline REEFMAN

  • Ultimate Champ
  • ****
  • Posts: 9766
  • Cred: 768
  • Gender: Male
  • Location: Jozi
Re: D.I.Y Non Return Slides
« Reply #9 on: December 30, 2011, 09:59:06 AM »
Great post Darren!  (clap) :+ cred:

As a matter of interest, have you seen the way Zeyn bends his slide clips... ?

http://www.ultimateangling.co.za/index.php/topic,6311.msg88159.html#msg88159

It's the way I do mine now.

Logged

Offline Nemesis.

  • The Karou Charou
  • Senior Member
  • **
  • Posts: 182
  • Cred: 66
  • Gender: Male
  • Location: Mandeni _ KZN Northcoast
Re: D.I.Y Non Return Slides
« Reply #10 on: December 30, 2011, 03:26:03 PM »
Quote from: REEFMAN on December 30, 2011, 09:59:06 AM
Great post Darren!  (clap) :+ cred:

As a matter of interest, have you seen the way Zeyn bends his slide clips... ?

http://www.ultimateangling.co.za/index.php/topic,6311.msg88159.html#msg88159

It's the way I do mine now.
Thanks Tony, yes I've seen Zeyn's way of bending the clip, works like a charm, have done a few in that fashion as well :uarocks
Logged
There's a fine line between fishing and just standing on the shore like an idiot.

Offline Rory

  • Ultimate member
  • ***
  • Posts: 1270
  • Cred: 175
  • Gender: Male
Re: D.I.Y Non Return Slides
« Reply #11 on: January 01, 2012, 12:20:01 PM »
Excellent post! Thank you for sharing, plus cred! :+ cred:  And the next project starts..... :hnthnt:
Logged

Offline Lenny

  • Ultimate Champ
  • ****
  • Posts: 2529
  • Cred: 124
  • Gender: Male
  • Catch and Release
  • Location: Struisbaai
Re: D.I.Y Non Return Slides
« Reply #12 on: January 04, 2012, 11:27:04 AM »
Nice Post !!  :+ cred:


I make mine just like that , they are very strong .
One thing I can add : When you bend the coils ,let the rod [or in Nems case the Bolt] do the work , what i mean is ,  make sure not to twist the Tig rod .
Logged
Self catering , family accommodation available  in Struisbaai . Contact Leon 0780394225

Offline Naruto

  • Senior Member
  • **
  • Posts: 566
  • Cred: 30
  • Gender: Male
  • Ultimate Freshie
  • Location: Pretoria
Re: D.I.Y Non Return Slides
« Reply #13 on: January 04, 2012, 12:11:09 PM »
 :tkx: :+ cred:
Logged
“Every search begins with beginner’s luck. And every search ends with the victor’s being severely tested.”

1.   “…whoever you are, or whatever it is that you do, when you really want something, it's because that desire originated in the soul of the universe. It's your mission on earth."

Offline adam

  • Ultimate member
  • ***
  • Posts: 623
  • Cred: 138
  • Gender: Male
  • The lighter the tackle, the bigger the fish!
  • Location: Patensie E.C.
Re: D.I.Y Non Return Slides
« Reply #14 on: January 04, 2012, 07:22:46 PM »
Excellent!  Will definitely try it sometime.    :+ cred:



Is this what you mean?
Logged
"I once caught a fish thiiiiiiiiss big, now pass another beer"

Offline Nemesis.

  • The Karou Charou
  • Senior Member
  • **
  • Posts: 182
  • Cred: 66
  • Gender: Male
  • Location: Mandeni _ KZN Northcoast
Re: D.I.Y Non Return Slides
« Reply #15 on: January 04, 2012, 07:41:12 PM »
Quote from: adam on January 04, 2012, 07:22:46 PM
Excellent!  Will definitely try it sometime.    :+ cred:



Is this what you mean?
Yep buddy, i always get the shivers tying a lekker trace to a swivel that is suspect, i even had swivels stretch a few MM!! <: Not a lekker thought to use R50 hooks, Skirts that cost R60 a pack, cable thats R70 a pack and then attach it to a 25cent swivel :lolo:
Logged
There's a fine line between fishing and just standing on the shore like an idiot.

Offline Lenny

  • Ultimate Champ
  • ****
  • Posts: 2529
  • Cred: 124
  • Gender: Male
  • Catch and Release
  • Location: Struisbaai
Re: D.I.Y Non Return Slides
« Reply #16 on: January 04, 2012, 08:01:15 PM »
Hectic Adam !!!
Logged
Self catering , family accommodation available  in Struisbaai . Contact Leon 0780394225

Offline Geno

  • Senior Member
  • **
  • Posts: 277
  • Cred: 5
  • Saving sheep one bullet at a time!
  • Location: Brits
Re: D.I.Y Non Return Slides
« Reply #17 on: January 05, 2012, 09:23:41 AM »
Great post!  :+ cred:

Do you guys reckon you can slide a carp head or suitably big bait for barbel in fresh water? :brbel:
Tunaman, what you think? I think casting distance would greatly improve.

Cheers,
Eugene
Logged

Offline VISCHAL

  • Senior Member
  • **
  • Posts: 51
  • Cred: 0
  • Gender: Male
  • Location: Durban
Re: D.I.Y Non Return Slides
« Reply #18 on: January 05, 2012, 12:29:09 PM »
 :+ cred:
Logged

Star

  • Guest
Re: D.I.Y Non Return Slides
« Reply #19 on: June 11, 2012, 06:20:27 PM »
@ Nemesis what wire/rod is that exactly and have you put it to a test.


Are guys out there using different material,I have been told to use stainless steel tig welding wire or spring steel.


Thanks in advance for any feed back.
Logged
Pages: [1] 2   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2026, SimplePortal